Stainless steel glass doors are common to everyone. They are mainly used in some large shopping malls, and the installation method also requires some skills. Do you know the installation method? Today, Luban home furniture installer introduced the installation process and precautions of stainless steel glass doors to you. Interested friends can learn about it.

一，不銹鋼玻璃門的安裝方法

1、 Installation method of stainless steel glass door

1.定位線。在不銹鋼玻璃門安裝開始時，固定玻璃間距和可移動玻璃門扇需要定位在一個統一的位置，并確定固定門框的方向，以及地面的高度和高度應測量門框頂部的位置。

1. Positioning line. At the beginning of the installation of stainless steel glass door, the fixed glass spacing and movable glass door leaf need to be positioned in a unified position, and the direction of the fixed door frame and the height and height of the ground should be determined. The position of the top of the door frame should be measured.

2.在門框頂部安裝限位槽。從子彈的線繪制兩個金屬裝飾板邊緣，然后通過側線安裝門框的頂部位置。

2. Install a limit slot on the top of the door frame. Draw two metal trim panel edges from the center line of the bullet, and then install the top position of the door frame through the side line.

3.金屬飾面的木質底部用原始預埋木磚上的膨脹螺栓或方木釘在木塊上，然后將金屬飾面粘在木質面上。

3. The wooden bottom of the metal facing is nailed to the wood block with expansion bolts or square wood on the original embedded wood bricks, and then the metal facing is glued to the wooden surface.

4.設備牢固地固定在門框上。根據子彈的線，門框被釘牢，然后膠合板用于確定門框的方向和形狀。固定后，然后包裹金屬裝飾表面。

4. The equipment is firmly fixed on the door frame. According to the center line of the bullet, the door frame is nailed, and then plywood is used to determine the direction and shape of the door frame. After fixing, wrap the metal decorative surface.

5.玻璃門扇裝置。不銹鋼玻璃門通過玻璃吸盤用厚玻璃吸入，然后使用吸盤將厚玻璃板抬起2至3人并將其豎立到設備位置。

5. Glass door leaf device. The stainless steel glass door is sucked with thick glass through the glass suction cup, and then the thick glass plate is lifted by the suction cup for 2 to 3 people and erected to the equipment position.

6.玻璃是固定的。兩個扁平方條在內托盤的內側和外側釘牢，厚玻璃夾在中間，但距離厚玻璃板約4毫米，然后在平木條上涂上貼面金屬板。它被粘在兩塊扁平木條和方木上。

6. The glass is fixed. Two flat square strips are nailed firmly on the inner and outer sides of the inner tray, and the thick glass is clamped in the middle, but about 4mm away from the thick glass plate, and then the veneer metal plate is coated on the flat wood strip. It is glued to two flat wooden strips and square timber.

7.注塑玻璃密封。在頂部根槽兩側的開放空間和底部玻璃槽的兩側，以及厚玻璃和門框柱的相對側，注入玻璃膠。

7. Injection glass seal. Inject glass glue into the open space on both sides of the top root groove, both sides of the bottom glass groove, and the opposite side of the thick glass and the door frame column.

8.在玻璃之間對接。具有固定部分的厚玻璃板需要由兩個或更多個部件組裝，因為寬度太大。兩個拼接件需要形成一個接頭，接頭間距應為2至3毫米。

8. Butt joint between glasses. Thick glass plates with fixed parts need to be assembled by two or more parts because the width is too large. Two splices need to form a joint, and the joint spacing should be 2 to 3 mm.

二，不銹鋼玻璃門安裝注意事項

2、 Precautions for installation of stainless steel glass door

1.安裝前，需要確保施工結束后內部裝修過程完成，并且定位的位置應嚴格按照規劃圖紙進行。

1. Before installation, it is necessary to ensure that the internal decoration process is completed after the construction is completed, and the positioning position should be carried out in strict accordance with the planning drawings.

2.玻璃門框頂部的限位槽的槽深在20到30mm之間，并且寬度優選地比玻璃的厚度大2至4mm用于注射。

2. The groove depth of the limit groove on the top of the glass door frame is between 20 and 30mm, and the width is preferably 2 to 4mm larger than the thickness of the glass for injection.

3.當外包金屬裝飾表面時，應將遮蓋的接縫放置在裝置玻璃兩側的。接縫方向需要準確和筆直。

3. When the metal decorative surface is wrapped, the covered joint shall be placed in the center of both sides of the device glass. The joint direction needs to be accurate and straight.

4.放置玻璃門扇時，玻璃杯的上部應插入門框頂部的限位槽中，然后玻璃的下部應放在線上，并且方向為兩側的門框應該是厚玻璃的兩側剛好覆蓋門框面向接縫的金屬框架，并且要求在桌子上看不到接縫。

4. When placing the glass door leaf, the upper part of the glass should be inserted into the limit slot on the top of the door frame, and then the lower part of the glass should be placed on the center line, and the door frame on both sides should be thick glass, and both sides of the door frame should just cover the metal frame facing the joint, and the joint should not be seen on the table.

5.密封玻璃膠時，注射順序應從一定間隙結束開始到結束，不應中途停止。

5. When sealing the glass glue, the injection sequence should start from the end of a certain gap to the end, and should not stop halfway.

6.在玻璃對接接頭的過程中，需要使用接頭的玻璃切割，固定玻璃后，應將玻璃粘在間隙中。填充后，塑料片應用塑料片壓平，使間隙構成清潔。均勻的直線，用干凈的布擦拭玻璃表面。

6. In the process of glass butt joint, the glass of the joint needs to be cut. After fixing the glass, the glass should be stuck in the gap. After filling, the plastic sheet shall be flattened to make the gap clean. Wipe the glass surface with a clean cloth in a uniform straight line.

以上就是為大家介紹的有關不銹鋼玻璃門的詳細的介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以的態度,為您提供服務http://diaolan88.com

The above is a detailed introduction about stainless steel glass doors. I hope it will help you If you have any questions, please contact us We will provide you with professional service http://diaolan88.com